Texas-instruments TMS320C645x DSP Manuel d'utilisateur Page 19
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
www.ti.com
EMAC Functional Architecture
The RMII interface has the same functionality as the MII, but it does so with a reduced number of pins,
thus lowering the total cost for an application. In devices incorporating many PHY interfaces such as
switches, the number of pins can add significant cost as the port counts increase. Table 3 summarizes the
individual EMAC and MDIO signals for the RMII interface.
The RMII interface does not include an MCOL signal. A collision is detected from the receive and transmit
data delimiters. The data signals are 2 bits wide, and a single reference clock must be provided to the
MAC, operating at 50MHz to sustain the same data rate as MII.
Table 3. EMAC and MDIO Signals for RMII Interface
Signal Name I/O Description
MTXD[1-0] O Transmit data (MTXD). The transmit data pins are a collection of 2 data signals comprising 2
bits of data. MTDX0 is the least-significant bit (LSB). The signals are synchronized to the
RMII reference clock and valid only when MTXEN is asserted.
MTXEN O Transmit enable (MTXEN). The transmit enable signal indicates that the MTXD pins are
generating nibble data for use by the PHY. It is driven synchronously to the RMII reference
clock.
MCRSDV I Carrier sense/receive data valid (MCRSDV). The MCRSDV pin is asserted by the PHY when
the network is not idle in either transmit or receive. The data on MRXD is considered valid
once the MCRSDV signal is asserted. The pin is de-asserted when both transmit and receive
are idle. The assertion of this signal is asynchronous to the RMII reference clock. This pin is
used in half-duplex operation only.
MREFCLK I Reference clock (MREFCLK). A 50MHz clock must be provided through this pin for RMII
operation.
MRXD[1-0] I Receive data (MRXD). The receive data pins are a collection of 2 data signals comprising 2
bits of data. MRDX0 is the least-significant bit (LSB). The signals are synchronized to the
RMII reference clock and valid only when MCRSDV is asserted. In 10 Mbps operation, MRXD
is sampled every 10th cycle of the RMII reference clock.
MRXER I Receive error (MRXER). The receive error signal is asserted for one or more reference clock
periods to indicate that an error was detected in the received frame. This is meaningful only
during data reception when MCRSDV is active. It is driven synchronously to the RMII
reference clock.
MDCLK O Management data clock (MDCLK). The MDIO data clock is sourced by the MDIO module on
the system. It is used to synchronize MDIO data access operations done on the MDIO pin.
The frequency of this clock is controlled by the CLKDIV bits in the MDIO control register
(CONTROL).
MDIO I/O Management data input output (MDIO). The MDIO pin drives PHY management data into and
out of the PHY by way of an access frame consisting of start of frame, read/write indication,
PHY address, register address, and data bit cycles. The MDIO pin acts as an output for
everything except the data bit cycles, when the pin acts as an input for read operations.
SPRU975B – August 2006 Ethernet Media Access Controller (EMAC)/Management Data Input/Output (MDIO) 19
Submit Documentation Feedback
- User's Guide 1
- 2 SPRU975B – August 2006 2
- Submit Documentation Feedback 2
- Contents 3
- Read This First 10
- Data Input/Output (MDIO) 11
- 1.3 Functional Block Diagram 12
- Introduction 13
- 2.1 Clock Control 14
- 2.2 Memory Map 15
- 2.3 System Level Connections 16
- EMAC Functional Architecture 17
- 2.5 Programming Interface 26
- 2.6 EMAC Control Module 37
- 2.8 EMAC Module 43
- 2.10 Packet Receive Operation 50
- 2.13 Transfer Node Priority 56
- 2.14 Reset Considerations 56
- 2.15 Initialization 57
- 2.16 Interrupt Support 60
- 2.17 Power Management 63
- 2.18 Emulation Considerations 63
- 3.1 Introduction 64
- EMAC Control Module Registers 65
- 4 MDIO Registers 66
- 4.1 Introduction 66
- MDIO Registers 67
- 5 EMAC Port Registers 81
- 5.1 Introduction 81
- Table 30 85
- Table 33 88
- Table 38 93
- Table 39 94
- Table 43 98
- Table 44 99
- EMAC Port Registers 100
- Table 47 102
- Table 48 103
- Field Descriptions 104
- Descriptions (continued) 105
- Descriptions 110
- Table 63 121
- Table 68 126
- Table 76 134
- Table 77 135
- Appendix A Glossary 145
- Appendix A 146
- Appendix B Revision History 147
Produits connexes et manuels pour Matériel Texas-instruments TMS320C645x DSP
(14 pages)2n Mobility Extension Application podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Akcesoria komunikacja 2n Mobility Extension Application.
Dostarczamy 1 pdf podręczników 2n Mobility Extension Application do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels